FW 190A-3 3D-Printed & coloured Interior on decal paper (for Eduard kit) QD48079

FW 190A-3 3D-Printed & coloured Interior on decal paper (for Eduard  kit)

Quinta 3D Decals

3D-Decal Working Tips

- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.

- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.

!!! Using decal softener solutions (Micro Set/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.

Operating procedure

1. Prepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).

2. Optionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.

3. Carefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.

4. Separate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).

5. To ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:

6. Squeeze a drop of CYA-glue out of the tube onto a separate surface.
7. Dip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.
8. Carefully put this miniscule drop onto plastic kit part.
9. Separate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.
10. Put the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.
11. Carefully and quickly position the 3D-Decal part.

The shipment of your order is usually done in the same day of your order date if the order is done before 16:00 local time. Otherwise, we ship in the next working day.

We use the following shipping companies and costs:

For Greece:

• Box Now (1-3 working days) from 3.00 euro. Free for orders above 50.00 euro.
  
• Geniki Taxydromiki (1-2 working days) from 5.80 euro. Free for orders above 50.00 euro.
• ACS (1-2 working days) from 5.90 euro. Free for orders above 50.00 euro.
• For ACS and Geniki Taxydromiki, there is available option for pick up from the local courier representative.

For Cyprus:

• Box Now from 4.00 euro.
  
• ACS from 12.00 euro.

For EU countries:

• National Post, no tracking (7-20 days) from 8.00 euro.
  
• DHL Economy with tracking (5-10 days) from 15.90 euro.
• DHL Express with tracking (1-3 days) from 22.90 euro.

Rest of the world:

• National Post or DHL from 29.00 euro.
  

The buyer retains the right to return the purchased item 14 days from the shipping day only if the item is not damaged or altered.